Ontario – Quinte Shores – Frankford
Corporation
Ontario
Quinte Shores
Frankford
Corporation
active
Sidney Thermal Technologies Inc. is a Canadian company distributing a liquid insulation product called TEMP-COAT®.
I PRODUCTS
TEMP-COAT® €œ101€?
Insul-Allâ„¢
II APPROVALS - ACCEPTANCE
GSA/NSN #8030 01 387 1027
Lloyd's Register of Shipping #SAS FOI0506
Approved: U.S. Coast Guard, MLCA Std 6300N P .35
Accepted for Certification by: USDA Accepted by: FDA
Approved by: Dept. of Energy
Accepted by: Navy Safety - Survivability
S.I.C. Code: 5033
All Ingredients TSCA Listed
III DESCRIPTION
TEMP-COAT®€œ101€? is a general purpose insulation which comes in liquid form. It is widely used as a rooftop insulation, but performs extremely well on piping, air and heat duct work, exposed water pipes, oxygen lines, water tanks, steam lines and has many other uses.
TEMP-COAT®€œ101€? provides an inexpensive alternative to the high cost of industrial insulations. Because it physically adheres to the surface that it is insulating, it significantly reduces corrosion and rust formations found under conventional insulations.
Insul-All™ is a reformulation of TEMP-COAT®"101" pointed to the homeowner and do-it yourselfer. Polymers are added increasing the products ease of application. Insul-All™ contains less than .001% ethylene glycol. May be applied to surfaces up to 225 F. 15 mil thickness provides an equivalence of R-18.
Make Up: TEMP-COAT®€œ101€? and Insul-AIIâ„¢ are a complete mixture of various silicas and ceramic beads immersed in a high quality latex base with acrylic binders. This combination of materials makes the product extremely light weight and pliable, therefore, it expands and contracts with the surface to which it is applied. The resiliency of TEMP-COAT®€œ101€? and Insul-AIIâ„¢ allow it to double as a leak stop even though it is not sold or warranted for that purpose.
Other Properties: TEMP-COAT®€œ101€? works well on boat and barge decks and other surfaces as a method of controlling the surface temperature.
TEMP-COAT®€œ101€? and lnsul-Allâ„¢ can be tinted virtually any medium to pastel color. The tinting does have some affect on the radiant effectiveness of the product.
Product Qualities: TEMP- COAT® €œ101€? works well on both convective and conductive heat and cold. When used in ways, which does not require solar reflective qualities, its effectiveness has different values. Unlike conventional insulation such as fiberglass batting, blankets, foam, fiber insulations, or calcium silicate type pre-formed insulation for piping or enclosures having temperatures below 400O F*, TEMP- COAT® €œ101€? is impervious to water and is not affected by salt water. As this product is a liquid, it forms a continuous covering and not sectioned as installed conventional products. It also forms an excellent weatherproof coating over the other forms of insulation.
ACCORDING TO RADIANT HEAT TEST RESULTS IN A ROOF TOP APPLICATION. TEMP-COAT® €œ101€? WHEN APPLIED TO A THICKNESS OF 15 MILS. PERFORMS AS WELL AS A 4" THICKNESS OF FOAM WITH AN R- 20 RATING.
* Test results for Roof Top Applications
Product Limits: TEMP-COAT® €œ101€? and Insul-Allâ„¢ aid in sealing leaks but is not sold as a leak-stop material. Product must he applied over a clean, dry, grease and dirt free substrate.
TEMP-COAT® €œ101€?s operating temperatures can be from –0oF to 400°F*. It can be applied to temperatures ranging from 45oF to 350°F**. On extremely warm to hot surfaces, beginning coats must be thin to avoid blistering.
** In some instances for temperatures 350oF to 400°F a mesh/membrane must be used and the High Heat Application Instructions must be followed.
IV. APPLICATION
Apply TEMP-COAT® €œ101€? /Insul-Allâ„¢ on any clean, dry substrate which is free from oil, grease, wax or dirt. A sufficient amount of Primer on all surfaces prone to rust and to prevent bleed through is recommended. Apply by use of brush, roller, airless spray or air assisted QuikGun. Strain product before spraying. Spray equipment requirement: 5.4 GPM, 28: 1 ratio airless sprayer or the air assisted "QuikGun". Allow product to dry between coats. This is a one-coat system with curing time of 24 hours under normal conditions.
Approximate Coverage: Spray: 60 SF per gallon at 15 mil thickness on a flat surface.
On Pipe: 20 mil thickness
4" O.D. LF per gallon = 56
8" O.D. LF per gallon = 24
12" O.D. LF per gallon = 15
Country of Ownership: Canada
Exporting: Yes
Primary Industry (NAICS): 416390 - Other Specialty-Line Building Supplies Wholesaler-Distributors
Primary Business Activity: Trading House / Wholesaler / Agent and Distributor
Products:
Temp-coat®, Temp-coat
No associations
LandOfFree
Sidney Thermal Technologies Inc. does not yet have a rating. At this time, there are no reviews or comments for this company.
If you have personal experience with Sidney Thermal Technologies Inc., we encourage you to share that experience with our LandOfFree.com community. Your opinion is very important and Sidney Thermal Technologies Inc. will most certainly appreciate the feedback.
Profile ID: LFCA-COD-O-19880